TN LCD display driver

T LCD screen adopts static driving mode. The so-called static driving refers to continuously applying driving voltages to the displayed pixel electrodes and common electrodes at the same time until the display time ends. Since the driving voltage has been maintained during the display time, it is called static driving. The following takes the most commonly used pen-segment TN liquid crystal display as an example. The pen-segment T LCD screenrealizes display through segmented display pixels. Segmented display pixel refers to the display pixel in a long bar shape, also known as a pen segment shape. In digital display, a seven-segment electrode structure is often used, that is, each digit is composed of a '8'-shaped common electrode and seven segment electrodes forming a '8'-shaped pattern, which are respectively arranged on two substrates, as shown in Figure 1. Shown. Figure 1 The electrode arrangement diagram of the seven-segment pen-segment liquid crystal display. The driving voltage of each pen segment is AC 3～5V, and the frequency is 32Hz, 167Hz, 200Hz. When working, the back electrode (COM) is continuously added to the A continuous square wave with a space ratio of 1/2. A continuous square wave with the opposite phase, the same amplitude and the same frequency as the voltage waveform on the back electrode is applied to the pen segment to be displayed, and then the pen segment to be displayed is added The alternating positive and negative voltage is twice the amplitude of the square wave, which should be greater than the threshold voltage of the liquid crystal display device 14h; and apply a voltage waveform on the back electrode that does not need to be displayed with the same phase and amplitude as the voltage on the back electrode. , Waveforms with the same frequency, no electric field can be formed on the pen segment, and of course it cannot be displayed. Figure 2 shows the principle and waveform diagram of a liquid crystal display drive circuit with a segment electrode. Figure 2 Principle and waveform diagram of a liquid crystal display drive circuit with a segment electrode Figure 2 (a) is an exclusive OR circuit. The input terminal A is a square wave oscillating pulse spoon generated by the oscillating circuit and is directly connected to the COM terminal of the LCD screen. The input terminal B can be connected to high and low (ON/OFF) levels to control the on and off of the electrode. The output terminal C of the XOR gate is connected to the front electrode (a, b, c, d, e, f or g) of the pen segment end of the liquid crystal display. The AC drive waveforms at both ends of the liquid crystal display (LCD) can be obtained from the XOR gate truth table shown in Figure 2(b), as shown in Figure 2(c). It can be seen that when the voltage phase of the two electrodes on the field is the same, the potential difference between the two electrodes is zero, and this field is not displayed; when the voltage phase of the two electrodes on this field is opposite, the potential difference between the two electrodes is For a square wave voltage with twice the amplitude, the field appears black. The driving of the liquid crystal display is very different from the driving of the LED. For LEDs, adding a constant on or off voltage at both ends of the LED can control its brightness or darkness. However, since the two poles of the LCD cannot be applied with a constant DC voltage, it brings complexity to the drive. Generally, a constant alternating square wave signal should be added to the common electrode of the LCD (usually the back electrode), and the required zero voltage or double amplitude alternating voltage is generated between the two electrodes of the LCD by controlling the voltage change of the front electrode. In order to achieve the control of the display screen on and off. Figure 3 shows the electrode configuration and static driving circuit diagram of the seven-segment liquid crystal display. The seven segments share a back electrode COM, and the front electrodes a, b, c, d, e, f, g are independent of each other, and each segment is driven by an exclusive OR gate. Figure 3 Electrode configuration and static driving circuit diagram of the seven-segment liquid crystal display At present, there are many LCD driving integrated chips on the market, and multiple LCD driving circuits can be integrated together, which is very convenient to use. The pen-segment static drive has two characteristics: ①The driving of each electrode is independent of each other and does not affect each other; ②During the display period, the driving voltage is maintained to make the liquid crystal fully driven. Therefore, compared with the dynamic drive described below, the static drive has the advantages of good contrast, high brightness, and fast response. The disadvantage of static driving is that each pen-shaped electrode requires a control element. When the number of digits displayed is large, the number of corresponding driving elements and lead terminals will be too much. Therefore, its application is limited and only suitable for bits. A few segment electrodes are displayed. Note: For the LCD screen, the following points must be paid attention to: (1) When driving the LCD screen, it is not advisable to apply DC voltage, otherwise it will cause electrolysis and electrode aging of the liquid crystal, which will greatly reduce the service life of the LCD screen. Therefore, The liquid crystal display must be driven by AC voltage, and the DC component in the AC component is limited to no more than tens of millivolts. (2) Since the change of the optical performance of the liquid crystal under the action of an electric field depends on the elastic deformation of the liquid crystal as an elastic continuum, the response time is long, so the effect of the alternating driving voltage does not depend on its peak value, and the frequency is less than 10 Hz. Below, the change in the transmittance of the liquid crystal is only related to the effective value of the applied voltage. (3) The liquid crystal cell is a capacitive load, and the resistance of the liquid crystal is negligible in most cases. It is non-polar, that is, the effect of positive pressure and negative pressure is the same.

Kimeery (HK) Industrial Limited is willing to push up our sleeves and wade into unknown territory with equal parts fearlessness and optimism.

Kimeery (HK) Industrial Limited didn’t receive any negative feedback from our customers before, which proves that customers have faith in us.

Technology upgrades can pay for themselves quickly by improving mobile phone lcd display and enabling employees to accomplish more in less time. It may be time to focus on cell phone lcd wholesale to ensure they run smoothly and efficiently.

mobile phone lcd display can be great additions to companies looking to improve the well-being of their employees, as well as increase the efficiency and productivity of their workers across the organization.

Overall, mobile phone lcd display may be a great way for manufacturers to expand their use of technology, but the price could present a significant hurdle for some businesses.